Quick answer
The most common reason a garage door will not close is a problem with the safety sensors near the floor: they are blocked, dirty, knocked out of alignment, or blinded by sunlight. After that, check for something in the door’s path, the lock button on the wall control, the remote battery, and the opener’s limit settings. If you see a broken spring, a snapped cable, or a door off its track, stop and call a professional.
A garage door that will not close is more than an annoyance. It leaves your home, your car, and everything in the garage open to anyone walking by. The good news is that many of the causes are simple, and you can check several of them yourself in a few minutes. Work through this list in order, from the most common and easiest to the most serious.
1. Check the safety sensors first
Every residential opener sold in the U.S. since 1993 has been required to include an entrapment protection system, and on most doors that means two small photo-eye sensors mounted on either side of the door, a few inches above the floor. They send an invisible beam across the opening. If anything breaks that beam, the door will not close, or it will start down and reverse.
- Look at the sensor lights. Most sensors have a small LED. A solid light usually means they are working and aligned. A blinking or missing light usually means a problem.
- Clear the path. A broom, trash can, toy, or even a spider web in front of a sensor can block the beam.
- Wipe the lenses. Dust and cobwebs build up on the lens over time. A soft dry cloth is all it takes.
- Check the alignment. If a sensor has been bumped, it may be pointing slightly off. Gently adjust it until both lights are steady.
- Watch for sun glare. In North Texas, low morning or evening sun shining straight into a sensor can blind it. If your door only refuses to close at certain times of day, glare is a likely cause. Shading the sensor or swapping its sides usually solves it.
2. Look for anything in the door’s path
Check the floor under the door and both tracks. A small object in a track, or something just inside the opening, can stop the door or cause it to reverse. Many openers also reverse if they feel unusual resistance as the door closes.
3. Check the wall control’s lock button
Many wall controls have a lock or vacation mode that disables remotes. If the wall button works but remotes do not, look for a lock button or a lock light on the wall control and turn it off.
4. Try a new remote battery
If the door closes from the wall button but not the remote, a dead remote battery or lost programming is the most likely cause. Replacing the battery or reprogramming the remote is a quick fix.
5. Check the opener’s limit and force settings
The close limit tells the opener where the floor is. If it is set wrong, the door may stop short or think it has hit something and reverse. Settings can drift over time, especially after a power outage or a repair. Follow your opener manual carefully, or have a technician adjust them, since force settings affect how the safety reverse works.
6. Look at the tracks and rollers
Bent tracks, loose brackets, and worn rollers can make the door bind as it closes. If the door shudders, grinds, or stops at the same spot every time, the hardware likely needs attention. This is a job for a professional, because adjusting tracks on a door under spring tension can be dangerous.
7. Stop if you see a broken spring, cable, or crooked door
Do not force the door. If a spring has a visible gap, a cable is loose or snapped, or the door is hanging crooked or off its track, stop using it, keep everyone clear, and unplug the opener. Pulling the emergency release on a door with a broken spring can make it fall. Call us at (817) 282-6273. We answer 24/7.
Our emergency repair page explains what to do while you wait, and our guide to signs your spring is about to break covers what a failing spring looks like.
How to close the door in the meantime
If the sensors are the problem and the door is otherwise working normally, many openers will close the door if you press and hold the wall button until the door reaches the floor. This bypasses the sensors, so watch the door the whole way down and keep people, pets, and cars out of the way. Get the sensors fixed as soon as possible, because they are an important safety feature.
When to call a professional
- The sensors are clean and aligned, but the door still will not close
- The door reverses for no clear reason after you adjust the settings
- You hear grinding, see a bent track, or notice frayed cables
- The opener hums but the door does not move
- Your opener is old enough that it may not have modern safety features
We repair openers from all major brands and install new LiftMaster openers. See opener repair and installation or garage door repair.
Frequently asked questions
Why does my garage door start to close and then go back up?
Usually the safety sensors are blocked or misaligned, or the opener is sensing resistance from binding tracks, worn rollers, or a force setting that needs adjusting.
Why does my door only close when I hold down the wall button?
Holding the button overrides the safety sensors on many openers. If that is the only way the door will close, the sensors are almost certainly blocked, dirty, misaligned, or failing.
Can sunlight really stop my garage door from closing?
Yes. Direct sunlight shining into a sensor can overpower the beam, especially in the early morning or late afternoon. Shading the sensor usually fixes it.

